JUNGLE Decorative Paints can be applied to various surfaces including cement (new or old), plasterboard, plaster of Paris, wood (new or old), plastic, glass and iron (new or old), provided they are free of humidity, well dry, smooth and have already been treated. Any loose or dusty paint, as well as any grease or rust, must be removed and the surface washed with suitable soap. Fill the surfaces to be decorated, if necessary, and apply a base coat that is suitable to the type of surface to be treated. Once the base coat is dry, apply the JUNGLE Range products as indicated below:
1) PRIMER 700. (Coverage 0.080 l/sqm) Apply a coat using a wool roller. Allow to dry for 4 hours at 20°C, then proceed to Point 2.
2) Place the EL 11K STENCILS over the entire surface to be treated and align the connection points between the various stencils. Proceed to Point 3 once the procedure is completed.
3) EL 630 already coloured. (Coverage 0.800 l/sqm) Using the stainless steel trowel, spread a 2-3 mm thick coat of product in the least uniform way painting the final strips with horizontal and slightly striated stokes. Remove the stencils and allow to dry for about 6 hours at 20°C then sand the surface lightly to remove any lumps. Proceed to Point 4. 4) PRIMER 700. (Coverage 0.100 l/sqm) Apply a coat using the wool roller; allow to dry for 4 hours at 20°C then proceed to Point 5.
5) EL 631 must be coloured prior to application using COLORI’ or the VALCLONE Dispensing System. The shades EL 631/500 - 631/501 - 631/502 cannot be coloured with COLORI’ but only using the Paint Dispenser, or directly by VALPAINT.
(Coverage 0.100 l/sqm) Apply two layers with a brush. Allow the first layer to dry for approx. 1 hour at 20°C before applying the second layer; use a 3 x 10 cm handle-free brush. Wet the bristles up to a maximum of 1-2 mm and apply the product with round strokes only, while adjusting the pressure accordingly to create light-dark nuances. Allow the second coat of EL 631 to dry for approx. 2 hours at 20°C before proceeding to Point 6.
6) EL 632 TRANSPARENT. (Coverage 0.200 l/sqm) Apply three layers with a wool roller and wait at least 1 hour before each successive application.
N.B.: All the above-mentioned phases must be completed without interruptions once they are started, while any areas that have already been coated must not be retouched. ELEFANT JUNGLE KIT: There are two JUNGLE KITS available in order to obtain the ELEFANT effect to decorate 3 sqm or 10 sqm.
PRODUCTS INCLUDED IN THE 3 SQM ELEFANT JUNGLE KIT: 0.550 l of PRIMER 700 - 2.320 l of EL 630 - 0.300 l of EL 631 (to be coloured with COLORI’ or with Dispensing Machine) - 0.900 l of EL 632 TRANSPARENT - 12 EL 11K STENCILS - N. 1 ADIPIT 500 PV 73.
PRODUCTS INCLUDED IN THE 10 SQM ELEFANT JUNGLE KIT: 1.800 l of PRIMER 700 - 8 l of EL 630 - 1 l of EL 631 (to be coloured with COLORI’ or with Dispensing Machine) - 3 l of EL 632 TRANSPARENT - 36 x EL 11K STENCILS - N. 1 ADIPIT 500 PV 73.

 

TECHNICAL DATA:

Dilution: all JUNGLE decorative paints are ready for use and must be shaken well before and during use.
Application temperature: between +5°C and +30°C.
Strength: when the paint has fully hardened, a breathable film develops which offers good resistance to knocks and normal abrasion.
Washability: 15 days after the cycle has been applied, the surface acquires its definitive properties, becoming breathable and washable with water or common neutral detergents.
Equipment cleaning: use water.
Storage: make sure that the can is tightly closed, even after use, and store at temperatures between +5°C and +30°C.
Stability: approximately 2 years.

SPECIFIC SAFETY INSTRUCTIONS:
avoid direct contact with skin. Protect eyes and face. In the event of contact, rinse immediately and thoroughly with water and consult a doctor. Do not wash equipment in watercourses, drains, etc.
USER ADVICE:
N.B.: the information provided here is, to the best of our knowledge, correct and accurate. However, given that the conditions in which the products are used are not under our control, we will not be held liable for any recommendations or advice we provide. All products required for creating the JUNGLE effect are sensitive to different painting techniques therefore it is important that the painting work is carried out entirely by same person.
Moreover, it is essential to follow the application instructions specific to each JUNGLE Range effect. Shades may vary compared to the catalogue by between 20% and 30%, as well as from one batch to another, thus it is advisable to carry out a small test before commencing the work.The manufacturer and the distributor shall not be held liable for possible variations between batches, or in cases where the batch number is illegible.
Should the batches be different, all the material must be mixed in a large container before beginning application, in order to avoid differences in colour once the product has been applied.

Check the stencils supplied with the JUNGLE KIT thoroughly before positioning them. In particular, check the quantity and integrity of the stencils to ensure the correct outcome of the desired decorative effect.