JUNGLE Decorative Paints can be applied to various surfaces including cement (new or old), plasterboard, plaster of Paris, wood (new or old), plastic, glass and iron (new or old), provided they are free of humidity, well dry, smooth and have already been treated.
Any loose or dusty paint, as well as any grease or rust, must be removed and the surface washed with suitable soap. Fill the surfaces to be decorated, if necessary, and apply a base coat that is suitable to the type of surface to be treated. Once the base coat is dry, apply the JUNGLE Range products as indicated below:
1) PRIMER 700 HAZELNUT 11. (Coverage 0.080 l/sqm) Apply a coat using a wool roller. Allow to dry for 4 hours at 20°C, then proceed to Point 2.
2) MZ 600 TRANSPARENT. (Coverage 0.140 l/sqm) Apply two coats using a wool roller. Allow to dry for about 2 hours at 20°C before applying the second coat. Add the second coat of MZ 600 TRANSPARENT and allow to dry for 2 hours at then proceed to Point 3.
3) TG 602 and TG 601 already coloured. (Coverage 0.080 l/sqm) Apply a thick layer of TG 602 with a 10 cm wool roller and paint a 15 - 20 cm wide strip moving from the left end towards the right end. While the applied product is still wet, use the 20 cm wide wool roller and apply a thick layer of TG 601 in a 90-100 cm wide vertical strip overlapping the previous one by 5 - 8 cm, in order to blend the two colours and create light-dark nuances.
Use the first roller again to paint another vertical strip of TG 602 about 25 - 30 cm wide overlapping the previous one made with TG 601 by about 5-8 cm, in order to create nuance effects.Continue applying paint in strips until completing the wall surface to be decorated. Allow to dry for approx. 2 hours at 20°C, then proceed to Point 4.
4) MZ 600 TRANSPARENT. (Coverage 0.140 l/sqm) Apply two coats using a wool roller. Allow to dry for about 2 hours at 20°C before applying the second coat. Add the second coat of MZ 600 TRANSPARENT and allow to dry for 2 hours at 20°C then proceed to Point 5.
5) Position the TG 1A STENCILS (left) and align the connection points between the stencils. The stencils must be fixed in vertical strips starting from the top left end and moving towards the bottom end. Use a pencil to mark the points when repositioning the successive stencils (Point 7). These marks may be removed with a rubber once work is completed. Once the first strip of stencils has been placed, proceed to Point 6.
6) TG 603 already coloured. (Coverage 0.090 l/sqm) Apply a coat of paint with the 10 cm wool roller over the entire surface covered with the TG 1A STENCILS. Remove the stencils and allow to dry for about 10 minutes at 20°C before proceeding to Point 7.
7) Position the TG 1B STENCILS (right) and align the connection points to form another strip alongside the one already formed with the TG 1A Stencils. Once the second strip of TG 1B STRIPS has been positioned, proceed to Point 8.
8) TG 603 already coloured. (Coverage 0.090 l/sqm) Apply a coat of paint with the 10 cm wool roller over the entire surface covered with the TG 1B STENCILS. Remove the stencils and allow to dry for about 10 minutes at 20°C before repeating Points 5, 6, 7 and 8 on the rest of the surface to be decorated. Proceed to Point 9.
9) VALFLOK 300 TRANSPARENT. (Coverage 0.200 l/sqm) Apply two coats using a wool roller and spread well. Allow to dry for approx. 1 hour at 20°C before applying the second coat.
N.B: All the above-mentioned phases must be completed without interruptions once they are started, while any areas that have already been coated must not be retouched. The TG 1A and TG 1B STENCILS must be repositioned several times and may lose their adhesive properties. If such is the case, spray the side of the stencil to be fixed to the surface with ADIPIT 500 PV 73 temporary spray that comes with the JUNGLE KIT. TIGER JUNGLE KIT: There are two JUNGLE KITS available in order to obtain the TIGERE effect to decorate 3 sqm or 10 sqm. PRODUCTS INCLUDED IN THE 3 SQM TIGER JUNGLE KIT: 0.270 l of PRIMER 700 HAZELNUT 11 - 0.900 l of MZ 600 TRANSPARENT - 0.500 l of TG 601 - 0.200 l of TG 602 - 0.300 l of TG 603 - 0.550 of VALFLOK 300 TRANSPARENT - 6 x TG 1A STENCILS (left) - 6 x TG 1B STENCILS (right) - 1 x ADIPIT 500 PV 73. PRODUCTS INCLUDED IN THE 10 SQM TIGER JUNGLE KIT: 0.900 l of PRIMER 700 HAZELNUT 11 - 3 l of MZ 600 TRANSPARENT - 1.700 l of TG 601 - 0.700 l of TG 602 - 1 l of TG 603 - 1.800 of VALFLOK 300 TRANSPARENT - 7 x TG 1A STENCILS (left) - 7 x TG 1B STENCILS (right) - 1 x ADIPIT 500 PV 73.

 

TECHNICAL DATA:

Dilution: all JUNGLE decorative paints are ready for use and must be shaken well before and during use.
Application temperature: between +5°C and +30°C.
Strength: when the paint has fully hardened, a breathable film develops which offers good resistance to knocks and normal abrasion.
Washability: 15 days after the cycle has been applied, the surface acquires its definitive properties, becoming breathable and washable with water or common neutral detergents.
Equipment cleaning: use water.
Storage: make sure that the can is tightly closed, even after use, and store at temperatures between +5°C and +30°C.
Stability: approximately 2 years.

SPECIFIC SAFETY INSTRUCTIONS:
avoid direct contact with skin. Protect eyes and face. In the event of contact, rinse immediately and thoroughly with water and consult a doctor. Do not wash equipment in watercourses, drains, etc.
USER ADVICE:
N.B.: the information provided here is, to the best of our knowledge, correct and accurate. However, given that the conditions in which the products are used are not under our control, we will not be held liable for any recommendations or advice we provide. All products required for creating the JUNGLE effect are sensitive to different painting techniques therefore it is important that the painting work is carried out entirely by same person.
Moreover, it is essential to follow the application instructions specific to each JUNGLE Range effect. Shades may vary compared to the catalogue by between 20% and 30%, as well as from one batch to another, thus it is advisable to carry out a small test before commencing the work.The manufacturer and the distributor shall not be held liable for possible variations between batches, or in cases where the batch number is illegible.
Should the batches be different, all the material must be mixed in a large container before beginning application, in order to avoid differences in colour once the product has been applied.

Check the stencils supplied with the JUNGLE KIT thoroughly before positioning them. In particular, check the quantity and integrity of the stencils to ensure the correct outcome of the desired decorative effect.